网站公告:
凯时app机械制造有限公司是一家集研发、生产 与贸易结合的工贸一体综合型机械制造企业。
全国服务热线:18032990897
产品展示
联系我们

贵宾销售热线:18032990897
售后服务专线:18937298880
微信:18032990897
传真:0319-5038333
邮箱:frank@paradisevending.net
地址:河北 省邢台市东郊

第六代 旋转式节省人工型,月省三千元

发布时间:2018/10/31
第六代 旋转式节省人工型,月省三千元

未标题-1.jpg

用途 Applications
  本机适用于建筑用的钢管翻新、除锈、喷 漆实行一次性机械化 完成,达到每条钢管统一洁净,油 漆 均匀的 效果,本机工作效率高,能 每分钟完成两条6米的速度,摆脱了已往用人工除锈,喷油的复杂程序,是 各大小建筑商钢管除锈的理想 设备。
  This machine is suitable for construction of pipe renovation, rust, paint mechanized complete one-off, to achieve unity of each pipe clean, paint a uniform effect, high working efficiency of the machine, to complete the two speed of 6 meters per minute, to get rid of the conventional artificial rust, complicated procedure of fuel injection, the size of the device is ideal for builders steel rust.
参数Technical parameters

型号

电压

功率

使用范围

调直效率

调直速度

理论重量

外形尺寸

 

Rated voltage

Power

Diameter Range

Estraigh enfficiency

Work Efficiency

weight

Overall dimensions

AY48-4

380V

10KW+0.2KW

Φ46-49

≤3°

18米/分钟

1100KG

2500*1030*1300

注意事项 Application notice
  1、本机适用于380V、频率50Hz、三相电源。使用前请阁下检查所使用的电源是否符合本机要求。 本机应避免雨淋及溅水,为阁下的安全起见,本机必须可靠 接地或安装漏 电开关。
  This applies to 380V, frequency 50Hz, three-phase power. Before use, check your power supply used by the machine meets the requirements. The machine should avoid rain and splashing water for your safety, the machine must be grounded or install GFCI.
  2、本机应安放在水平的地面,确保机器的平稳,进、出管口分别要与 其它建筑物保持6米以上距离
  The machine should be placed at ground level, to ensure a smooth machine, into and out of the nozzle, respectively, to maintain more than 6 meters away from buildings and other
  3、新机使 用时应当 检 查变速箱、链条等传动部件的机油是否正常,如有 停转或出现异常响声时 应切断电源停 机检查,排除故障后方可使用。
  Should check the gearbox, drive chains and other parts of a new machine oil is normal, if stalling or abnormal sound should cut off the power down to check, troubleshooting before use.
  4、喷油时把已 调好的油漆灌入油桶内以 确保流量,达到最佳性能。
  When the injection has been tuned paint poured into the barrel to make sure that the flow to achieve the best performance.
  5、每次使用完后,必须 要定期保养全机 链条加润滑油(黄油),一般在7-15天左右加油一次。
  after each use, regular maintenance of the whole machine must lubricate the chain (butter), typically 7-15 days refuel again.
  6、本机只适用于48mm的钢管,凡是有严 重变 型,有焊口或开口的钢管都 不能在本机上操作。
  the machine is only available in 48mm pipe, where there are serious variations, there is an opening or pipe weld can not operate on this unit.
  7、操作人员不能够佩带手套,保持与本机入 口一米以上距离,防 止近距离接触入口旋 转伦,避免伤手。
  The operator can not wear gloves to keep up with the machine more than one meter from the entrance to prevent close contact with inlet swivel Lun, avoid hand injuries.

关闭