网站公告:
凯时app 机械制造有限公司是一家集研发、生产与 贸易结合的工贸一体综合型机械制造企业。
全国服务热线:18032990897
产品展示
联系我们

贵宾销售热线:18032990897
售后服务专线:18937298880
微信:18032990897
传真:0319-5038333
邮箱:frank@paradisevending.net
地址:河北省邢台市东郊

第三代(压轮式双除锈型,除锈干净彻底)

发布时间:2018/10/31
第三代(压轮式双除锈型,除锈干净彻底)

未标题-1.jpg

用途 Applications
  本 机适用于 建筑 用的钢管翻新、除锈、喷漆实行一次性机械化 完成,达到每条钢管统一洁净, 油漆均匀的效果,本机工作效率高,能每分钟完成 两条6米的速度,摆脱了已往用人工除锈, 喷油的复 杂程序,是各大小建 筑商钢管除 锈的理想设备。
  This machine is suitable for construction of pipe renovation, rust, paint mechanized complete one-off, to achieve unity of each pipe clean, paint a uniform effect, high working efficiency of the machine, to complete the two speed of 6 meters per minute, to get rid of the conventional artificial rust, complicated procedure of fuel injection, the size of the device is ideal for builders steel rust.
参数Technical parameters

型号

电压

功率

使用范围

调直效率

调直速度

理论重量

外形尺寸

 

Rated voltage

Power

Diameter Range

Estraigh enfficiency

Work Efficiency

weight

Overall dimensions

AY48-4

380V

10KW+0.2KW

Φ46-49

≤3°

18米/分钟

1100KG

2500*1030*1300

注意事项 Application notice
  1、本机适用于380V、频率50Hz、三相电源。使用前请阁下 检查所使用的电源是否符合本机要求。 本机应避免雨淋 及溅水,为阁下的安全起 见,本机必须可靠接地或 安装漏电开关。
  This applies to 380V, frequency 50Hz, three-phase power. Before use, check your power supply used by the machine meets the requirements. The machine should avoid rain and splashing water for your safety, the machine must be grounded or install GFCI.
  2、本 机应安放在 水平的地面,确保机器的平 稳,进、 出管口分别要与 其它建筑物 保持6米以上距离
  The machine should be placed at ground level, to ensure a smooth machine, into and out of the nozzle, respectively, to maintain more than 6 meters away from buildings and other
  3、新机使用时应当检查变速箱、链条等传动部件的机油是否正常,如有停转或出现异 常响声时应 切断电源 停 机检查,排除故障后方 可使 用。
  Should check the gearbox, drive chains and other parts of a new machine oil is normal, if stalling or abnormal sound should cut off the power down to check, troubleshooting before use.
  4、喷油时把已调好的油 漆灌入油桶内 以确保流量,达到最佳性能。
  When the injection has been tuned paint poured into the barrel to make sure that the flow to achieve the best performance.
  5、每次使用完后,必须要定期保养全机链条加润滑 油(黄油),一般在7-15天左右加油一次。
  after each use, regular maintenance of the whole machine must lubricate the chain (butter), typically 7-15 days refuel again.
  6、本机只适用于48mm的钢管,凡是有严重变型,有 焊口或开口的钢管都不能在本机上操作。
  the machine is only available in 48mm pipe, where there are serious variations, there is an opening or pipe weld can not operate on this unit.
  7、操作人员不能够佩 带 手套,保持与本机 入口一米以上距离, 防止近距离接 触 入口旋转伦,避免伤手。
  The operator can not wear gloves to keep up with the machine more than one meter from the entrance to prevent close contact with inlet swivel Lun, avoid hand injuries.

关闭